![]() ![]() ![]() In order for a dog to truly understand a command, he needs to repeat the command about 100 times and in varying environments (different locations, people, situations and with distractions) Reward as soon as your dog’s bottom hits the floor Give the hand cue (no treat in this hand) AND say “sit” at the same time Step Five: Test your dog’s understanding of the verbal and hand cues combined Release the treat and say “sit” as soon as the dog’s bottom hits the floor Give your hand cue, with a treat between your fingers so you’re ready to reward your dog once he or she sits Step Four: Test your dog’s understanding of the hand cue Release the treat as soon as your dog’s bottom hits the floor Give hand cue and say “sit” at the same time Hold hand flat, palm up, with a treat between your fingers Step Three: Using the hand signal and verbal cue together If your dog lays down afterwards, don’t use a lot of words but motion and encourage your dog to stand back up Release the treat AND say “sit” at the same time as soon as your dog sits Step Two: Give the cue as your dog performs the behavior Move treat over bridge of your dog’s nose and slightly upward to push him into a natural sit Step One: Show your dog the action without verbal cues These are the steps from the video above: How to teach “sit” to your Great Pyrenees The dog should rise onto all fours – as soon as the dog is in a standing position, say “yes, stand,” then release the treatīelow is a video that demonstrates all four steps: Take the treat and slowly pull it away from your dog’s face, but in a slightly upward fashion Your dog should rise into a sitting position to get itĪs soon as your dog is in an “up” position, say “yes, up,” then release the treatįrom the sitting position, tether the treat to your dog’s nose so they know you have it Lure your dog back into a sit by tethering the treat to his nose and moving your hand back up Lure your dog into a down by moving the treat to the ground slowlyĪs soon as your dog is in a “down” position, say “yes, down,” then release the treat Starting from a sitting position, tether the treat to your dog’s nose Keep the treat “tethered” to your dog’s nose and move it up over the bridge of his nose and continue up from there, so your dog’s nose is pointed at the ceiling, this will typically cause him to sit down instinctivelyĪs soon as the dog’s bottom touches the ground, say “yes, sit,” then release the treat Place treat between pointer finger and thumb – make sure your dog knows you have something he wants ![]() If you prefer not to teach your dogs the commands “up” and “stand,” check out the next section instead. Some people like to teach the “sit” and “down” commands separately (and leave out the “up” and “stand” commands altogether). Your dog will be less confused if he has two different commands to describe these two different movements, even though the ending position is the same. To your dog, the movement from standing up to sitting down feels very different from the movement from laying down to sitting up. So, “sit” and “up” both refer to a sitting position? Yes. “Stand” refers to standing up from a sitting position. “Sit” refers to going into a sit position from standing, whereas “up” refers to going into a sit position from laying down. Some people find that the commands “sit,” “down,” “up,” and “stand” are easiest to teach to your dog in combination. How to teach “sit,” “down,” “up,” and “stand” to your livestock guardian dog For detailed information on all of these steps, see my instructions, How to Start Obedience Training with Your Dog. You’ll also want to take frequent breaks and gradually increase the level of distractions in the environment as your dog progresses. Get your dog’s favorite award readily available You’ll want to start your dog training by teaching your dog these simple commands before moving onto more challenging ones, such as “off” (i.e., no jumping), “speak,” and “be quiet.” (For more on these commands, check out my articles, The 4 Commands Your Livestock Guardian Dog Must Know and Train Your Livestock Guardian Dog to Speak and Be Quiet.)įor the most effective training sessions, take the following steps:Ĭhoose a training environment with no distractions The easiest commands to teach your dog are: Whether you’re raising your Great Pyrenees or other livestock guardian dog (LGD) breed to be a beloved family pet or a livestock guardian, your dog will need basic training. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |